SSD Not Detected After a Power Cut? What to Do First

The lights flicker, the power goes off, and when it comes back your computer cannot find its SSD. Or a laptop battery runs completely flat in the middle of an update, and afterwards the drive shows up with the wrong name or a capacity of a few megabytes. Solid state drives are fast and have no moving parts, but they are not immune to a sudden loss of power. Here is what can go wrong, what not to do, and how the data can usually still be reached.

Why an SSD can be hurt by a power cut

An SSD does not store your files in the order you see them. Its controller spreads data across the flash memory chips and keeps a map, often called the translation table or FTL, recording where every piece of data really lives. That map is constantly changing as you work, and to keep things quick the drive holds the latest version in fast working memory before writing it back to flash.

If power disappears at the wrong moment, the drive can lose the most recent changes to that map, or be left with a map that is half-written. Many business and server SSDs have capacitors that give them enough time to save everything when power drops. Most consumer SSDs in home PCs and laptops do not have full power-loss protection, so they rely on their firmware to recover cleanly when power returns. Usually it does. Sometimes it cannot, and the controller refuses to present the drive normally.

Common symptoms after a power loss

  • The SSD is no longer listed in the BIOS or UEFI setup, or the PC goes straight to “no bootable device”.
  • The drive appears, but with the wrong capacity, such as 0 bytes, a few MB or 1 GB.
  • The drive shows a generic or odd model name instead of its usual one. For example, some SSDs using Phison controllers identify themselves as “SATAFIRM S11” when their firmware has failed to start properly.
  • Windows sees the drive but asks you to initialise it, or the partition shows as RAW or unallocated.
  • The drive has become read-only, or freezes the computer whenever you try to open files.

Some of these can also be caused by a loose connection or a BIOS setting that changed when the power went off, so it is worth ruling those out first.

Quick checks that are safe

  1. Check the BIOS settings. A power cut or flat CMOS battery can reset the SATA mode (AHCI, RAID or Intel RST) or the boot order. If the storage mode changed, setting it back can make a healthy drive reappear.
  2. Reseat once. On a desktop, check the SATA data and power cables, or that an M.2 SSD is fully seated and screwed down. Then stop. Repeated plugging and unplugging does not help a drive with a firmware fault.
  3. Look, do not write. If the drive appears in Windows Disk Management, look at what it reports, but do not click anything that changes the disk.

What not to do

  • Do not initialise, format or create a new partition. Windows offers this whenever it cannot read a disk. On an SSD, a format can trigger TRIM, which tells the drive that everything can be erased.
  • Do not run a secure erase or “sanitise” from the manufacturer’s toolbox. These are designed to wipe the drive and reset it to factory state. They may make the drive work again, but empty.
  • Do not update the firmware yet. A firmware update is sensible on a healthy drive with a backup. On a drive that has just failed, it can overwrite the information needed to rebuild the map.
  • Do not leave it running recovery software for hours. If the controller is struggling, constant reads can push it further. If the drive has a worn-out or failing flash chip, it may also get worse with use.

Some manufacturers publish a “power cycle” procedure that leaves the drive powered on but idle so it can try to rebuild its tables. It is intended to get the drive working again rather than to protect your files, so if the data matters, get advice first.

How the data is recovered

A lab first works out whether the problem is a firmware fault, a failed component on the board, or worn or damaged flash memory. For many SSDs with a firmware fault, specialist equipment can put the controller into a technician mode, rebuild access to the translation table and copy the data off to a healthy drive. Where the controller itself has failed, the work is more involved, and results depend heavily on the model and whether the drive uses hardware encryption tied to that controller.

The earlier the drive comes in, before anyone has formatted it, updated it or reset it, the better the chances. Find out more about our SSD data recovery service, including NVMe and M.2 SSD recovery.

Preventing it next time

  • Use a small UPS on a desktop PC or home server if your area has frequent power cuts.
  • Do not let a laptop run completely flat during updates; plug it in first.
  • Shut down properly rather than holding the power button whenever possible.
  • Keep a current backup, because an SSD can fail without warning for many reasons, not only power loss.

Get help from Data Retrieval

If your SSD disappeared or changed after a power cut, stop using it and call us on 020 7064 4996. We offer a free assessment with no obligation, or you can request a quote online.